Mixing Procedure

Mixing procedure of Line Guard
	(1) Shuzai and Kokazai of polymer cement emulsion are poured into a container.
	(2) The paints are mixed with a stirrer for about three minutes.
	(3) S Compound and C Compound are added little by little into the paint and mixed for about five minutes to get the uniform material.

Mixing Procedure of Pillar Coat
	(1) Shuzai and Kokazai of polymer cement emulsion are poured into a container.
	(2) The paints are mixed with a stirrer for about three minutes.
	(3) S Compound is added little by little into the paint and mixed for about five minutes. (Caution) In case of spraying, clear water is added for 1-1.5 litter for coordination of stickiness.

---

Test Results

Chart A: Test results of Pillar Coat

	test items	Test Results	Method of tests
basic characteristics	Test of permeating water with a pressure	0.14	According to JIS A-1404 (display of the ratio of permeated water)
	Test of sucking water	0.57	According to JIS A-1404 (display of the ratio of sucked water)
	Test of attachment power	26kg/square cms	adhesive strength test by the Architecture Laboratory of the Minstry of Construstion
	Test of strongness against bending	28kg/square cms	According to JIS A-1404
	Test of strongness against compression	150kg/square cms	According to JIS A-1404
	Test of strongness against abrasion	1.5kg/500 times	Tabor abrasion tester
	Test of strongness against shock	50cm/1000g	Du-Pont impact tester
durability	Water-proof test	24kg/square cms	Test of attachment power by adhesive strength test by the Architecture Laboratory of the Minstry of Construction (permeated for two years)
	Weather-proof test	30kg/square cms	Test of attachment power by adhesive strength test by the Architecture Laboratory of the Minstry of Construction (exposed in outdoors for two years)
	Weather-proof test for procedure	More than 9H	Hardness test of the pencil (weather-o-meter 1000hours)
	Stability test for freezing and dissolution	35kg/square cms	Test of attachment power by adhesive strength test by the Architecture Laboratory of the Minstry of Construction *1
	Durability test against salty water	More than 9H	Hardness test of the pencil (permeated for one month)
	Durability test against salty water	More than 9H	Hardness test of the pencil (permeated for one month)
	Durability test against alkali	More than 9H	Hardness test of the pencil (permeated for one month)
	Durability test against acid	3H	Hardness test of the pencil (permeated for one month)

*1 (40 degrees x 12 hours, 10 degrees x 12 hours) x 20 cycles

Chart B: Elution Tests of Line Guard

Name of the tested material	The number of the test	Analyzed items
		Sn	Cd	As	Pb	PCB	Hg	Cu
Line Guard	K459	not detected <0.1	not detected <0.002	not detected <0.02	not detected <0.01	not detected <0.0005	not detected <0.0005	0.08

Method of Line Guard measurement

Sn	JIS K 0102 63.1 Method of measuring briliantness
Cd	JIS K 0102 55.2 Method of measuring atomic briliantness
As	JIS K 0102 61.1 Method of measuring briliantness
Pb	JIS K 0102 54.2 Method of measuring atomic briliantness
PCB	Notice No.59 by the Environment Agency gas chromatographic analysis rules
Hg	Notice No.59 by the Environment Agency Method of measuring atomic briliantness
Cu	JIS K 0102 52.2 Method of measuring atomic briliantness

*The unit is mg/l. The method of elution tests follow the Notice No.13 by the Environment Agency.

home	next